SOLVENT SEAL 30%

            DOWNLOADS:

Usage

Cures, seals, hardens, dust-proofs in one easy application.

VOC-compliant, non-yellowing acrylic curing and sealing compound for all horizontal concrete floors. Contains proprietary UV stabilizers.

Compliances

Federal EPA VOC

ASTM -C-1315, Type 1, Class A

ASTM -C-156 (Method of Testing)

ASTM -C-309, Type 1, Clear

AASHTO-M-148, Type 1, Transparent

NOVDOCK 13 YF

TT-C-800A

Asphalt and Vinyl Asbestos Tile Institute

Code of Federal Regulations Title 40, Part 59

Features

Contains 78% more solids than ASTM-C-309 cures

Covers 50% more than ASTM-C-309 cures

Applied costs are 30% less than ASTM-C-309 cures

Cures, seals, hardens, dust-proofs in one easy application

Retards moisture exchange, giving additional protection for tile, paint, carpeting, etc.
Helps prevent efflorescence

Can be used for both interior and exterior

Reduces expensive job site cleanup

Passes 500-hour salt-spray test

Solids remain stable under attack of most oils, salts, alkalis, fungi and many mineral acids

An excellent anti-spalling material

Appearance

Component - water clear

pH: neutral

Flash point: Cleveland Open Cup above 80°F/27°C

Viscosity: Ford Cup No.4: 20 seconds

Weight: 7.9 lbs at 77°F/3.5 kg at 25°C

Skinning: None

Cold stability: Down to -8°F/-22°C

Acid & alkali resistance: Good

Wearing Quality: Excellent

Coverage

Curing/sealing new concrete (ASTM 1315): 300 sq. ft./gal. (7.4 sq. m/L)

Curing/sealing aged concrete: 400-600 sq. ft./gal (9.8-14.7 sq. m/L)

Drying Time

Packaging

5 gal./18.9 L pails

55 gal./208 L drums

Application

CURING NEW CONCRETE

Surface must be sound and properly finished. Application can be made as soon as surface water has disappeared and slab can support the weight of an applicator. Apply at 300-400 sq. ft./gal. (7.4-9.8 sq. m/L). Application may vary depending upon the porosity and texture of the surface. With any high solids acrylic, over-application may highlight surface imperfections and trap out-gassing, causing surface bubbles. If a high gloss is desired, use multiple light coats.

SEALING NEW CONCRETE

For an excellent sealer and added protection to concrete cured with product, apply a second coat after 28 days of curing. If not previously applied when curing concrete, apply two coats, second coat four hours after first coat. Area to be sealed must be cleaned and free of all foreign matter such as dirt, rubber marks, paint, etc. Apply at 400-600 sq. ft./gal. (9.8-14.7 sq. m/L), on dry surface. Apply with spray, brush, long-nap roller or lambs wool applicator. Spray-applied for best results. Spray uniformly to form a continuous film.

DUST PROOFING/SEALING AGED CONCRETE

Surface must be structurally sound and free of foreign matter such as grease, oil, dirt or incompatible sealers and coatings. Unitex CITRI-CLEAN should be used as a degreaser and to remove rubber tire marks, followed by a thorough rinse with clean water. Surface must dry prior to application.

Two coats are necessary for maximum protection. Apply second coat at least four hours after first.

Limitations

Will not eliminate forklift burn. Will not provide bond to cementitious adhesives. Tests should be conducted to determine bondability with new products. Test panel should be made prior to application on exposed aggregate, concrete block, stone, precast or colored concrete.

Colored concrete should be allowed to cure 28 days prior to sealing.

Test application should be left for the time specified by the stone manufacturer.

Not recommended for use around pools or fountains.

Do not dilute product or alter in any way

Cleanup

EQUIPMENT: Uncured material can be removed with Unitex CITRI-CLEAN or other approved solvent. Cured material can only be removed mechanically.

MATERIAL: Collect with absorbent material. Flush area with water. Dispose of in accordance with local, state and federal disposal regulations. 

Cautions

Contains petroleum distillate, keep away from heat and open flame.

Avoid prolonged breathing of vapor or repeated skin contact.

Use in well-ventilated area.

For industrial use only.